Anodized Machined Pins

Pins and Foot Rests

Pipe SizeFemaleMale
3/4"PF-.75W
1"PF-1W, PF-1WC*PM-1
1 1/4"PF-1.25WPM-1.25
1 1/2"PF-1.50WPM-1.5
2"PF-2WPM-2

Unless otherwise specified, all pins are machined to fit the inside of schedule 40 pipe. All pins have a smooth finish and are bright dipped anodized.

Pin has slot opening large enough to allow the use of two nylon washers.

The male end is standard size, and the female end is sized for using two washers.

*Female closed top for crows nest railing.

Pipe SizePart Number
3/4"PH-.75
1"PH-1
1 1/4"PH-1.25
1 1/2"PH-1.5
2"PH-2

Typical usage: Pivoting/removable sun shade tops and learning post backrests

Uses 3/8″ NOM hardware for fastening. Commonly used the Marine Tower Shade Boses

Tower Boss and Shade

SizePart NumberSuggested Usage
1-5/16" Dia x 1-1/4"TSB-1021", 1-1/4" & 1-1/2" Pipe
1-5/16" Dia x 4"TSB-1031", 1-1/4" & 1-1/2" Pipe
1-5/8" Dia x 2"TB-1041-1/4" & 1-1/2" Pipe
1-7/8" Dia x 2"TSB-1051-1/2" & 2" Pipe

*This Boss is threaded 1/2-13 and used primarily to mount lights.

Tower shade base is threaded for 3/8-16 hardware. The design of our 4″ long base allows the user to bandsaw the base into any length desired. Both ends are tapped 3/8-16 and the base has a hole all the way through. Commonly used with the half pin for removable tower shade and pivoting station on backrest.

Pipe SizePart Number
3/4"PMF-.75W
1"PMF-1W
1 1/4"PMF-1.25W
1 1/2"PMF-1.5W
2"PMF-2W

This wide pin combination includes two nylon washers and stainless steel socket head screws.

Part NumberPivot Angle
QRPC-90-W90° w/washers

These pin combinations assemblies include two nylon washers that eliminate aluminum to aluminum and any possible galling.

Quick release pin combinations pivot 90° and can be locked in two positions.

Ideal for folding Sun Shades, T-Tops, Tower, etc.

anodized machined half pin with knob

Half Pin with Knob

1 1/4″ & 1 1/2″ available.

anodized machined swivel pivot

Swivel Pivot

For 1-1/2″ Pipe

Part Number
PBY-1.5-PIVOT

Designed to allow the wake board arch to fold in either direction by removing the locking knob.

Pipe SizePart Number
3/4"PBY-.75
1"PBY-1
1 1/4"PBY-1.25
1 1/2"PBY-1.5
2"PBY-2

All breakaways come complete with stainless steel hardware.

SizeLengthPart Number
3/4"2"PA-.75
1"2"PA-1
1-1/4"3"PA-1.25
1-1/2"5"PA-1.5
2"5"PA-2

Used to align and space apart two pieces of pipe being welded together.

Improves weld ability and joint strength.
Controls weld gap, ensures each weld is exactly the same.

Part NumberSize
COS-.75P3/4" Pipe
COS-1P1" Pipe
COS-1.25P1-1/4" Pipe
COS-1.5P1-1/2" Pipe
COS-2P2" Pipe

This product is designed to help the fabricator add anything that can be imagined without having to weld to the existing structure where welding is not practical, ladders, general purpose outfittings, and used with threaded antenna mount, you can add antennas, aft lights and GPS systems simply.

SizePart Number
3/4"EM-.75
1"EM-1
1-1/4" or 1-1/2"EM-2

Ear size 3/4″, 2″W x 1-1/2″ H x 1/4″ thick with 1/4″ hole
Ear size 1″, 2-1/4″ W x 1-3/4″ H x 3/8″ thick with 5/16″ hole
Ear size 1-1/4″ or 1-1/2″, 2-1/2″ W x 2″ H x 1/2″ thick wit 3/8″ hole

When mounting ear is used with standard female pin, the pin can pivot approximately 180° from side to side

Hinge Block Assembly with Washers

Hinge Block
Cope Mount
HBA-1.25CM RH
HBA-1.25CM LH
Flat Surface Mount Style
HBA-1.25FM RH
HBA-1.25FM LH

Typical usage is where a flat surface exists.

Assembly includes: Hinge block, nylon washers, 1NOM male pin and screw

The hinge block assembly is the idea way to attach a retractable foot rest bar to the perfect leaning post. With this application the hinge block assembly has to be welded. The hinge block assembly fits 1-1/4″ and 1-1/2″ NOM pipe. Usage requires one left hand and one right hand part.

Foot Rest Assembly

Part NumberWith Washers
FPH-10290°
FPH-10210°

Welded-On Method

Assembly includes: 1 NOM female pin, pivot mount, screw & nylon washers if indicated

This foot rest assembly includes two nylon washers that eliminate aluminum to aluminum galling.
10° foot rest assembly can be used where the learning post legs are more vertical or leaning aft.
Typical usage: Foot rests on leaning posts and ice cooler restraings, fits all pipe sizes 1″ and larger.

Foot Rest Assembly – Angle Mount

Part NumberBolt-On Method
FRA-100RHYes
FRA-100LHYes

Assembly includes: Angle bracket, two nylon washers, 1″ NOM female pin & screw

This foot rest assembly can be installed by bolting. Works great on flat surfaces.
If weld-on style is going to be used, simple band saw off the flange to the desired length and weld the assembly in place. Normally this type of installation is on the inside of the main legs of the leaning post to allow the foot rest bar to hang flush with the support legs.
Typical usage: Leaning posts and consoles

Part NumberColor
BRP-100WWhite
BRP-100BBlack
TT-6Aluminum

Assemblies include: Delrin back plate, anodized aluminum mount plate for 1″ pipe and self locking hardware.

Part NumberSize
SLEV-1011-5/16" ID x 8" LONG

Fits over 1″ NOM pipe and 1-1/2″ oval tubing

Application: Leaning post back rest support, this sleeve fits over 1″ pipe and 1-1/2″ oval tubing smuggly and slip fits into the inside of a standard 1-1/2″ ID opening flush mount rod holder. This sleeve eliminates the gap between the backrest pipe or tubing and the large opening of the rod holder.

Part NumberSize
TT-2162" X 16" X 1/4" Thick